SVKM NMIMS Global University

Infrastructure

Details of Laboratories

Lab Name: ME-L1 – Internal Combustion Engine and Refrigeration and Air-conditioning

Sr. No.	Parameters	Details
1	Lab Area	66.49 sq. m (Room No 117)
2	Lab In Charge	Prof. Yogesh Sonawane & Prof. Dattatray Doifode
3	Lab Technician	Mr. Mahendra Patil
4	Lab Investment	Rs. 34,11,620/-
5	List of Major Equipment’s	4 Cylinder 4 Stroke MPFI Petrol Engine. Single Cylinder 4 Stroke Diesel Engine with EGR. ICE Plant Test rig. Air Conditioning Test rig. Heat Pump Test rig. Electrolux (Absorption) Refrigeration system. Vapour Compression Refrigeration system. Vortex Tube Refrigeration system.
6	Practical’s Conducted in Laboratory	Performance test on Petrol Engine. Performance test on Diesel Engine. Morse Test on Petrol Engine. Trial on vapour compression refrigeration system. Trial on ICE Plant test rig. Study and trial on air conditioning system. Study and trial on heat pump test rig. Trial on Electrolux (absorption) refrigeration system. Trial on vortex tube refrigeration system.

Lab Name: ME-L2 - Thermal Engineering and Turbo Machinery

Sr. No.	Parameters	Details
01	Lab Area	96.73 sq.m (Room No 118 )
02	Lab In Charge	Prof. Dattatray Doifode Prof. Satish Patil
03	Lab Technician	Mr. Suresh Patil
04	Lab Investment	2075146
05	List of Major Equipments	Two Stage Reciprocating Air Compressor Test Rig. Combine Separating and Throttling Calorimeter. Flue Gas Analyser Model C 9000 Surface Condenser (Heat Exchanger) Centrifugal Blower Test Rig Bomb Calorimeter. Pelton Wheel Test Rig 1Kw Apparatus Kaplan Turbine Test Rig 1Kw Apparatus Francis Turbine Test Rig 1Kw Apparatus Centrifugal Pump Test Rig 1HP
06	Practical’s Conducted in Laboratory	Determination of calorific value of fuel by Bomb calorimeter. Study & trial on two-stage reciprocating air compressor. Trial on centrifugal air blower. Determination of Dryness fraction of steam by using Combine Separating and Throttling Calorimeter. Performance evaluation of surface condenser. Flue gas analysis using emission measuring instruments. To study the Pelton wheel Turbine To study the Francis Turbine To study the Kaplan Turbine To conduct a test on centrifugal pump

Lab Name: ME-L3 – CAD Lab

Sr. No.	Parameters	Details
1	Lab Area	66.51 Sq m (Room No 314 )
2	Lab In charge	Prof. Mohammed Juneduddin
3	Lab Technician	Mr. Amol Mahajan
4	Lab Investment	Rs.2416770
5	List of Major Equipment’s	Computers -25 (Intel Core i5 RAM 8 GB SSD 512 G Web Cam) Smart Board (Senses 65" Inbuilt) Printer (Make: Brother)
6	List of Software’s	Ansys Academic Teaching software Mech & CFD. Ansys-Space Claim 3D Software SolidWorks 3D software. Autodesk’s Inventor Professional AutoCAD 2023
7	Practicals conducted in laboratory	Part Modelling of machine elements using any one of the CAD software's. Assembly Modeling of assembly or sub-assembly of engineering products using any one of the CAD Software's. Drafting of Parts and Assembly of engineering assembly using any one of the CAD software's. Structural analysis problems to be solved using Ansys software. Understand various creating and editing commands in Any CAD software Draw machine element using keys, cotter, knuckle, bolted and welded joint. CFD Analysis for internal flow set-ups CFD Analysis for external flow set-ups

Lab Name: ME-L4 – Heat Transfer

Sr. No.	Parameters	Details
1	Lab Area	72.8 sq. m (Room No 317)
2	Lab In Charge	Dr. Hitesh Thakare
3	Lab Technician	Mr. Mahendra Patil
4	Lab Investment	Rs. 3,32,222/-
5	List of Major Equipment	Thermal Conductivity of Insulating Powder Thermal Conductivity of Metal Rod Thermal Conductivity of composite Wall. Natural Convection test setup Forced Convection test setup Pin fin apparatus Heat Exchanger (water to water and air to air). Stefan’s Boltzmann test rig Emissivity Apparatus Critical heat flux apparatus
6	Practical Conducted in Laboratory	Determination of thermal conductivity of Insulating Powder, Composite Wall, and Metal Rod. Determination of heat transfer coefficient for Natural and Forced Convection. Determination of performance of pin fin. Determination of Stefan Boltzmann constant. Determination of emissivity of a test plate. Performance of Parallel Flow / Counter Flow/cross flow Heat Exchanger. Determination of critical heat flux

Lab Name: ME-L5 - Material Science and Metallurgy and Mechatronics

Sr. No.	Parameters	Details
1	Lab Area	66.73 sq.m (Room No 318)
2	Lab In Charge	Dr. Amol Badgujar, Dr. Md. Modassir Hussain
3	Lab Technician	Mr. Suresh Patil
4	Lab Investment	Rs 1229289
5	List of Major Equipment’s	Rockwell Hardness Testing Machine Brinell Hardness Testing machine Trinacullar Metallurgical microscope with camera. Attachment Magnaflux Test Rig. Dye penetrant testRig Standard Metallurgical Microstructure Set Jominy End Quench Hardness Test app. With Quenching Fixture and Muffle Furnace Erichsen Cupping Test. Potentiometer Displacement Sensor. Capacitive Water Level Sensor. Optical Encoder for Angle and Speed Measurement Trainer Kit DC Servomotor- Speed Control Trainer Study of Electro-Pneumatic Trainer Electro-Hydraulic Trainer kit PLC Trainer Kit Temperature Controller Using PID Trainer
6	Practical’s Conducted in Laboratory	Erichsen Cupping Test Rockwell & Brinell Hardness Test Magnaflux Test, Dye penetrant test Specimen Preparation for Microscopy Study and drawing of microstructures of plain carbon steels of varying carbon percentage Study and drawing of microstructures of heat treated Steels Jominy End Quench Test Study and demonstration of various types of sensors. To design a Pneumatics Circuit on Pneumatic trainer kit To design a Hydraulics and Electro-Hydraulics Circuit on Hydraulic trainer kit. Programming of Microprocessor and Microcontroller Programming on PLC. Control using PID controller.

Lab Name: ME-L6 – Theory of Machine

Sr. No.	Parameters	Details
1	Lab Area	66.73 Sq. m (TOM I: Room No 319) & 66.73 Sq. m (TOM II: Room No 324)
2	Lab In charge	Prof. Bhushan Behede
3	Lab Technician	Mr. Amol Mahajan
4	Lab Investment	Rs.1096621
5	List of Major Equipment’s	Epicyclic Gear Train and Holding Torque Apparatus. Coriolli’s Component of Acceleration Apparatus. Cut Section of Synchromesh Gear Box Static & Dynamic Balancing Apparatus. Universal Governor Apparatus. Motorised Gyroscope Slip & Creep Measurement in Belt Drive Apparatus. Transverse Vibration setup (Computerised) Forced Vibration setup with Interface System Forced Transmissibility Unit Motion Transmissibility Unit Cam Analysis Machine App. Rope Brake Dynamometer - Motorised set up Single Rotor System - Viscous Damping
6	Practical’s conducted in laboratory	Verification of principle of gyroscope Study of epicyclical gear train To study the dynamic balancing machine and to balance a rotor To determine the natural frequency of damped vibration To verify natural frequency of torsional vibration To determine critical speed of a single rotor system To determine transverse natural frequency of a beam To determine the frequency response curve

Lab Name: ME-L7 – Metrology and Quality Control

Sr. No.	Parameters	Details
1	Lab Area	66.73 Sq. m (Room No 320)
2	Lab In charge	Prof. Satish Patil
3	Lab Technician	Mr. Amol Mahajan
4	Lab Investment	Rs.1114097
5	List of Major Equipment’s	Slip Gauge Set Steel 83 PC Surface Roughness Tester Floating Carriage Micrometer Profile Projector Tool Makers Microscope- METZER Gear Roll Tester Auto collimeter with Angle dekkor Vernier Calliper Digital Vernier Calliper Outside Micrometre Vernier Height Gauge Mechanical Comparator Stand Pneumatic comparator
6	Practical conducted in laboratory	Determination of linear and angular dimensions of given composite part using precision/non precision measuring instruments Error determination with linear / angular measuring instruments Calibration of measuring instrument. Example –Dial gauge, Micrometre, Vernier. Verification of dimensions & geometry of given components using Mechanical & Pneumatic comparator Determination of geometry & dimensions of given composite object using profile projector Measurement of thread parameters using floating carriage diameter measuring machine. Measurement of spur gear parameters using Gear Tooth Vernier, Span, Gear Rolling Tester Analyse the fault in given batch of specimens by using seven quality control tools for engineering application.

Lab Name: Drawing Hall

Sr. No.	Parameters	Details
1	Lab Area	136.7 sq. m (Room No 203)
2	Lab In Charge	Prof. Yogesh Sonawane
3	Lab Technician	Mr. Mahendra Patil
4	Lab Investment	Rs. 6,26,697/-
5	List of Major Equipment’s	Drawing Table Drawing Board
6	Practical’s Conducted in Laboratory	Lines, lettering and dimensioning. Geometrical Constructions. Orthographic projections. Projections of points and straight lines. Projections of planes. Projections of solids. Section of solids. Isometric Projections

Lab Name: Workshop

Sr. No.	Parameters	Details
1	Lab Area	206.58 sq. m (Room No 124)
2	Lab In Charge	Prof. Mohammed Juneduddin.
3	Lab Technician	Mr. Naval Patil / Mr. Mahendra Lohar
4	Lab Investment	Rs. 5206246.60/-
5	List of Major Equipment’s	Lathe Machine with All Accessories. Universal Milling Machine. Shaping Machine. Drill Machine (Portable). Tool and Cutter Grinder Machine. CNC Lathe Machine. CNC Milling machine.
6	Practical’s Conducted in Laboratory	Lathe Machine, Types of lathes, Major Parts, cutting tool Turning Operations. Making a job with the process plan involving plain, steps and taper turning as well thread cutting as operation on a centre lathe. Preparation of process, planning sheet of a job including operation such a milling, drilling and shaping. Making a spur gear using universal dividing head on milling machine. To develop a manual part program of a given component on CNC Lathe using G and M codes. (Making a Job by using CNC Lathe) To develop a manual part program of a given component on CNC Milling machine using G and M code. (Making a Job by using CNC Milling)

Lab Name: Basic Workshop (114)

Sr. No.	Parameters	Details
1	Lab Area	203.05 sq. m (Room No)
2	Lab In Charge	Prof. Mohammed Juneduddin
3	Lab Technician	Mr.Narendra Patil / Mr.Gajanan Patil / Mr.Yogesh Chaudhari
4	Lab Investment	Rs. 48,45,083/-
5	List of Major Equipment’s	Radial Drill Machine Surface Grinder Power Saw Bench Grinder TIG Welding MIG Welding Spot Welding Wood Lath Machine
6	Practical’s Conducted in Laboratory	Welding Shop. Fitting Shop. Carpentry Shop. Plumbing Shop. Sheet Metal Shop.

List of Classrooms

Classroom Details: Class Room No. 309, 310, 311 (IInd Floor)

Sr. No.	Parameters	Details
1	Classroom Area	136.70 Sq. m
2	Facilities	Smart Board (Senses 75" ) with Internet White Board PA System Wi-Fi Central Air Conditioner Chairs for students 70 nos. Ceiling Fans Lights Podium Acoustic Walls for Noise Reduction Electric Plug in Sockets for Laptop / Phone Charging

Classroom Details: Tutorial Room No. 306 (IInd Floor)

Sr. No.	Parameters	Details
1	Tutorial room Area	61.83 Sq. m
2	Facilities	White Board Wi-Fi Central Air Conditioner Benches Ceiling Fans Lights Electric Plug in Sockets for Laptop / Phone Charging

List of Faculty Rooms

Room No 308

Sr. No.	Parameters	Details
1	Faculty Area (308)	HOD Cabin (10 Sq. m), Department Office (10 Sq. m) and Faculty Cubicles for 6 Faculties (66.5 Sq. m)
2	Facilities	Desk and Chair Personal Computers Visiting Chair Wi-Fi and LAN Storage Space with locks Central Air Conditioner Ceiling Fans Lights Electric Plug in Sockets for Laptop / Phone Charging Common Printer, Copier and Scanner

Room No 312

Sr. No.	Parameters	Details
1	Faculty Room Area 312	31.66 Sq. m (Faculty Cubicles for 4 Faculties)
2	Facilities	Desk and Chair Personal Computers Visiting Chair Wi-Fi and LAN Storage Space with locks Central Air Conditioner Ceiling Fans Lights Electric Plug in Sockets for Laptop / Phone Charging